Design of 4-Channel Injector Cleaner and Tester Using Ultrasonic Waves
Keywords:
Design, 4 channel injector cleaner, ultrasonic wavesAbstract
The injector is a key component in the fuel system of a vehicle engine. If dirt or deposits accumulate, it can interfere with the fuel spraying process and reduce engine efficiency. By having their own injector cleaning tool, vehicle owners can save on the costs usually incurred for cleaning services at a repair shop. The design of the 4-channel injector cleaner and tester utilizes ultrasonic waves of the DA-968 type. Testing was conducted using the injector cleaner, ultrasonic wave device, and injector cleaner. Cleaning the injectors with the ultrasonic wave cleaner for 3-5 minutes resulted in a cloudy or dirty appearance. The injector tester was tested for 1 minute with a 5-minute cleaning cycle in the ultrasonic wave cleaner. All four injectors showed normal results with a smooth and even cone-shaped spray pattern. This study demonstrates that the 4-channel injector cleaner using ultrasonic waves of type DA-968 can be an effective and efficient solution for cleaning clogged injectors. This device can help restore engine performance to optimal conditions.
References
[1] H. Usui, T. Ishibashi, H. Matsuo, K. Watanabe, and K. Ando, “Visualization of acoustic waves and cavitation in ultrasonic water flow,” Solid State Phenom., vol. 314, pp. 186–192, 2021, doi: 10.4028/www.scientific.net/SSP.314.186.
[2] X. Shi, H. Xu, and L. Yang, “Removal of formation damage induced by drilling and completion fluids with combination of ultrasonic and chemical technology,” J. Nat. Gas Sci. Eng., vol. 37, pp. 589–598, 2017, doi: 10.1016/j.jngse.2016.11.062.
[3] H. Lais, P. S. Lowe, T. H. Gan, and L. C. Wrobel, “Numerical modelling of acoustic pressure fields to optimize the ultrasonic cleaning technique for cylinders,” Ultrason. Sonochem., vol. 45, pp. 78–87, 2018, doi: 10.1016/j.ultsonch.2018.02.045.
[4] V. Morkun and O. Kravchenko, “Evaluation of ultrasonic cleaning process,” Nauk. Visnyk Natsionalnoho Hirnychoho Univ., no. 3, pp. 117–124, 2021, doi: 10.33271/nvngu/2021-3/117.
[5] D. Radziuk and H. Möhwald, “Ultrasonically treated liquid interfaces for progress in cleaning and separation processes,” Phys. Chem. Chem. Phys., vol. 18, no. 1, pp. 30–46, 2016, doi: 10.1039/c5cp05142h.
[6] X. Huang, Q. X. Wang, A. M. Zhang, and J. Su, “Dynamic behaviour of a two-microbubble system under ultrasonic wave excitation,” Ultrason. Sonochem., vol. 43, pp. 45–56, 2018, doi: 10.1016/j.ultsonch.2018.01.012.
[7] A. V. Dengaev et al., “Chemical viscosity reduction of heavy oil by multi-frequency ultrasonic waves with the main harmonics of 20–60 kHz,” Fluids, vol. 8, no. 4, p. 136, 2023, doi: 10.3390/fluids8040136.
[8] M. Ehsani, H. Doan, and A. Lohi, “A comprehensive review of membrane fouling and cleaning methods with emphasis on ultrasound-assisted fouling control processes,” Korean J. Chem. Eng., vol. 38, no. 8, pp. 1347–1365, 2021, doi: 10.1007/s11814-021-0832-2.
[9] K. Przybysz, A. Lipkiewicz, E. Małachowska, M. Dubowik, and P. Przybysz, “Assessment of efficiency and anilox-roll condition after ultrasonic cleaning,” Coatings, vol. 13, no. 10, p. 1699, 2023, doi: 10.3390/coatings13101699.
[10] R. Park et al., “Root canal irrigation system using remotely generated high-power ultrasound,” Ultrason. Sonochem., vol. 90, p. 106168, 2022, doi: 10.1016/j.ultsonch.2022.106168.
[11] D. Chen, L. K. Weavers, and H. W. Walker, “Ultrasonic control of ceramic membrane fouling by particles: Effect of ultrasonic factors,” Ultrason. Sonochem., vol. 13, no. 5, pp. 379–387, 2006, doi: 10.1016/j.ultsonch.2005.07.004.
[12] R. Zhang, Y. Huang, C. Sun, L. Xiaozhen, X. Bentian, and Z. Wang, “Study on ultrasonic techniques for enhancing the separation process of membrane,” Ultrason. Sonochem., vol. 55, pp. 175–183, 2019, doi: 10.1016/j.ultsonch.2018.12.041.
[13] A. Amiri Delouei, H. Sajjadi, and G. Ahmadi, “Ultrasonic vibration technology to improve the thermal performance of CPU water-cooling systems: Experimental investigation,” Water, vol. 14, no. 24, p. 4000, 2022, doi: 10.3390/w14244000.
[14] G. Zhu et al., “Mechanism and application of laser cleaning: A review,” Opt. Lasers Eng., vol. 157, p. 107130, 2022, doi: 10.1016/j.optlaseng.2022.107130.
[15] M. U. Khan, F. Rehman, M. Saleem, H. Elahi, T. H. Sung, and H. Jabbar, “Optimum driving of ultrasonic cleaner using impedance and FFT analysis with validation of image processing of perforated foils,” Appl. Sci., vol. 13, no. 12, p. 6991, 2023, doi: 10.3390/app13126991.
[16] S. A. Aktij, A. Taghipour, A. Rahimpour, A. Mollahosseini, and A. Tiraferri, “A critical review on ultrasonic-assisted fouling control and cleaning of fouled membranes,” Ultrasonics, vol. 108, p. 106228, 2020, doi: 10.1016/j.ultras.2020.106228.
[17] T. Yamashita and K. Ando, “Low-intensity ultrasound induced cavitation and streaming in oxygen-supersaturated water: Role of cavitation bubbles as physical cleaning agents,” Ultrason. Sonochem., vol. 52, pp. 531–541, 2019, doi: 10.1016/j.ultsonch.2018.11.025.
[18] F. Yuan, X. Zhao, Z. Wu, Y. Ding, and Q. Yang, “Washing performance of microbubbles on porous media,” J. Water Process Eng., vol. 58, p. 104761, 2024, doi: 10.1016/j.jwpe.2023.104761.
